View all our industries

Our industries

Time to calibrate?

Secure your quality and reduce defects through Tool Calibration and Accredited Quality Assurance Calibration.​
power tool calibration, tool testing, metrology, machine capability test
Sluiten

How to increase quality in manual bonding

3 minute(s) to read Juli 22, 2021

For certain applications, it may be useful to apply adhesives and sealants manually rather than automatically. Planners and users should note several factors in order to achieve a consistently high quality.

1. Material pressure regulator against pump impact

The so-called pump impact often has a negative effect on the manual application of adhesive. At the changeover point from the material pump’s start lift to low lift, short-term pressure fluctuations may occur that lead to increased or reduced material leakage at the applicator. It is important that the system is configured correspondingly well and the pressures are set correctly. The use of a material pressure regulator can minimize the impact. This helps with clean and even application.

2. Optimum temperature conditioner

Modern adhesives increasingly require a temperature conditioner to be able to be processed precisely. Epoxy resin adhesives, for example, are processed at temperatures between 40° and 60° C. Consistent and accurate temperature control is crucial along the entire system from the pump to the hose to the applicator. The applicator should therefore be designed specifically for heated systems and be well insulated to avoid injury.

3. Minimize the influence of the hose

Due to the trend for tempering the adhesive, the material hose must also be heatable and withstand high pressures due to the higher-viscosity material, this increases its weight and volume. When choosing the hand applicator, attention should therefore be paid to a rotating coupling, so the worker can move flexibly and is not hampered by the hose. The use of a balancer, which the applicator and hose can be hung on, is also recommended. This carries the system’s weight and therefore reduce the burden on the worker.

4. Note the tool ergonomics

The ergonomics of the tool itself plays a major part in working productively and producing precise results. The applicator should be well balanced, have a large handle and if possible an additional handle. An additional handle helps balance the device better and prevents premature fatigue. In addition, the trigger affects the ergonomics: Pneumatic triggers are advantageous because the user doesn’t have to use as much force.

5. Even material flow

Producing an even adhesive bead is a particular challenge in manual applications. In practice, so-called hammer heads are a common problem in particular, for example, too much material applied at the beginning or at the end of the application. Devices that allow the material flow to be controlled provide a good solution. This distributes the material evenly and it can be individually adjusted depending on the component, application and application speed. This prevents hammer heads, reduces rework and improves the application’s overall quality and productivity.

 
Manual applicator Bonder X
 
Manual applicator Bonder X
 
Manual applicator Bonder X
Manual applicator Bonder X
Bonder X: Our solution for excellent manual bonding
Bonder X: Our solution for excellent manual bonding
The Atlas Copco Bonder X hand applicator is specially designed for working with medium and high-viscosity materials. The small and ergonomic tool features an additional handle and a pneumatic trigger that requires less pressure. For good accessibility and less strain on the operator, the material hose can be connected to the applicator by a rotating joint. For maximum flexibility, fix the connection for material supply in three positions: top, bottom and side. Special heat protection avoids injuries when working with hot material. A special valve technology prevents “hammer heads" at the beginning of the adhesive bead and improves the application’s quality.
 
The Atlas Copco Bonder X hand applicator is specially designed for working with medium and high-viscosity materials. The small and ergonomic tool features an additional handle and a pneumatic trigger that requires less pressure. For good accessibility and less strain on the operator, the material hose can be connected to the applicator by a rotating joint. For maximum flexibility, fix the connection for material supply in three positions: top, bottom and side. Special heat protection avoids injuries when working with hot material. A special valve technology prevents “hammer heads" at the beginning of the adhesive bead and improves the application’s quality.
Contact our experts for manual bonding!
Contact our experts for manual bonding!
 
  • Automotive